ANTI-BACTERIA STICKY MAT of Kosan Technology Material Ltd.

Product

ANTI-BACTERIA STICKY MAT
  • ANTI-BACTERIA STICKY MAT
PE+Cu Anti bacterial mat is already popular in South Korea. 
We supply as sticky mat , it can be used in clean area

Our recommended products and services

WTI & WTO / WINDOW INSIDE & OUTSIDE TAPES

WTI A / WINDOW INSIDE TAPES WITH ACRYLIC STRIPE INSIDE For inside sealing between windows / doors and building (walls, conservatories,etc) for quick and easy installation. Product advantages: high elasticity and flexible adaptation, compensates joint movement low inherent rigidity and at the same time high ultimate tensile strength for easy and effective application air tight, wind proof and vapour diffusion impermeable driving rain and water resistant special fleece surface to enable plastering, painting or pasting over with self-adhesive strip for easy installation Construction of window sealing tapes: Window sealing tapes are laminates made from two polypropylene non-woven combined with special membrane in the middle. It guarantees a proper amount of Sd coefficient. Sd coefficient determines how thick a layer of air must be, to put the same resistance to vapor as a membrane. The lower amount of Sd coefficient, the higher vapor-thigness of the membrane. Product has a special acryl glue ribbon, allowing installation to door or window frame, also in unfavorable weather. Ir could be also equipped with butyl glue ribbon, what allows it to stick to the wall. It eliminates necessity of using assembly glue. In our products we are using high quality acryl and butyl butyl glue. Our window sealing tapes are compatibile with glues, plasters, paints etc. It could be used in places, whereis necessity of using high vapor-thigness products. Assembly instruction: 1. Preparing the surface: Window hole should be prepared properly. First of all, window or door hole must be cleaned and primed all over the surface. In case, when wall is rugged, it should be equalized with cement mortar in order to ensure proper glue adhesion. 2. Preparing the window: Before sticking tapes to window, frame should be degrease. Frame must be dry and clean. Next step is to fit on the window in order to check distances between window and hole corners and proper tapes selection. 3. Sticking tapes to the window: Window sealing tapec setup should be made in this sequence: 1) Lower window area 2) Sides of window areas 3) Upper window area Vapor-tight tape (blue) should be sticked to inner side of frame, while vapor-permeable tape (grey) to outer side. After that its possible to install yhe window, stick outside tape to the wall and fill the gap with polyurethane foam. After removing ekscess of polyurethane foam, stick inside tape to the wall. In case of easy Access to window its possible to stick tapes after installing window. 4. Installing the window: Window installation should be done according to producent reccomendation. WTI AB(01) / ONE-SIDED WINDOW INSIDE TAPES WITH BUTYL AND ACRYLIC STRIPE For inside sealing between windows / doors and building (walls, conservatories, etc) for quick and easy installation. WTI AB(02) / TWO-SIDED WINDOW INSIDE TAPES WITH BUTYL AND ACRYLIC STRIPE For inside sealing between windows / doors and building (walls, conservatories, etc) for quick and easy installation. WTI B / WINDOW INSIDE TAPES WITH BUTYL STRIPE INSIDE For inside sealing between windows / doors and building (walls, conservatories, etc) for quick and easy installation. WTI A / WINDOW INSIDE TAPES WITH ACRYLIC STRIPE INSIDE For inside sealing between windows / doors and building (walls, conservatories,etc) for quick and easy installation. Product advantages: high elasticity and flexible adaptation, compensates joint movement low inherent rigidity and at the same time high ultimate tensile strength for easy and effective application air tight, wind proof and vapour diffusion impermeable driving rain and water resistant special fleece surface to enable plastering, painting or pasting over with self-adhesive strip for easy installation Construction of window sealing tapes: Window sealing tapes are laminates made from two polypropylene non-woven combined with special membrane in the middle. It guarantees a proper amount of Sd coefficient. Sd coefficient determines how thick a layer of air must be, to put the same resistance to vapor as a membrane. The lower amount of Sd coefficient, the higher vapor-thigness of the membrane. Product has a special acryl glue ribbon, allowing installation to door or window frame, also in unfavorable weather. Ir could be also equipped with butyl glue ribbon, what allows it to stick to the wall. It eliminates necessity of using assembly glue. In our products we are using high quality acryl and butyl butyl glue. Our window sealing tapes are compatibile with glues, plasters, paints etc. It could be used in places, whereis necessity of using high vapor-thigness products. Assembly instruction: 1. Preparing the surface: Window hole should be prepared properly. First of all, window or door hole must be cleaned and primed all over the surface. In case, when wall is rugged, it should be equalized with cement mortar in order to ensure proper glue adhesion. 2. Preparing the window: Before sticking tapes to window, frame should be degrease. Frame must be dry and clean. Next step is to fit on the window in order to check distances between window and hole corners and proper tapes selection. 3. Sticking tapes to the window: Window sealing tapec setup should be made in this sequence: 1) Lower window area 2) Sides of window areas 3) Upper window area Vapor-tight tape (blue) should be sticked to inner side of frame, while vapor-permeable tape (grey) to outer side. After that its possible to install yhe window, stick outside tape to the wall and fill the gap with polyurethane foam. After removing ekscess of polyurethane foam, stick inside tape to the wall. In case of easy Access to window its possible to stick tapes after installing window. 4. Installing the window: Window installation should be done according to producent reccomendation. WTI AB(01) / ONE-SIDED WINDOW INSIDE TAPES WITH BUTYL AND ACRYLIC STRIPE For inside sealing between windows / doors and building (walls, conservatories, etc) for quick and easy installation. WTI AB(02) / TWO-SIDED WINDOW INSIDE TAPES WITH BUTYL AND ACRYLIC STRIPE For inside sealing between windows / doors and building (walls, conservatories, etc) for quick and easy installation. WTI B / WINDOW INSIDE TAPES WITH BUTYL STRIPE INSIDE For inside sealing between windows / doors and building (walls, conservatories, etc) for quick and easy installation. WTO AB(02) / TWO-SIDED WINDOW OUTSIDE TAPES WITH BUTYL AND ACRYLIC STRIPE Vapour permeable membrane TOU Outside is dedicated to seal joints between the jamps and the door or window frames from the external side of the partition Product advantages: permanent outer sealant high elasticity – compensates for joint movement extreme temperature and weather resistant bitumen compatible Benefits: extra strong adhesive strength. fully covered adhesive. very soft and smooth fleece. four fingerlifts – it is possible to pull off the tape wearing working gloves. application from -10°C. 30 % time saving. high diffusion grade. high tensile strength for easy installation. Construction of window sealing tapes: Window sealing tapes are laminates made from two polypropylene non-woven combined with special membrane in the middle. It guarantees a proper amount of Sd coefficient. Sd coefficient determines how thick a layer of air must be, to put the same resistance to vapor as a membrane. The lower amount of Sd coefficient, the higher vapor-thigness of the membrane. Product has a special acryl glue ribbon, allowing installation to door or window frame, also in unfavorable weather. Ir could be also equipped with butyl glue ribbon, what allows it to stick to the wall. It eliminates necessity of using assembly glue. In our products we are using high quality acryl and butyl butyl glue. Our window sealing tapes are compatibile with glues, plasters, paints etc. It could be used in places, whereis necessity of using high vapor-thigness products. Assembly instruction: 1. Preparing the surface: Window hole should be prepared properly. First of all, window or door hole must be cleaned and primed all over the surface. In case, when wall is rugged, it should be equalized with cement mortar in order to ensure proper glue adhesion. 2. Preparing the window: Before sticking tapes to window, frame should be degrease. Frame must be dry and clean. Next step is to fit on the window in order to check distances between window and hole corners and proper tapes selection. 3. Sticking tapes to the window: Window sealing tapec setup should be made in this sequence: 1) Lower window area 2) Sides of window areas 3) Upper window area Vapor-tight tape (blue) should be sticked to inner side of frame, while vapor-permeable tape (grey) to outer side. After that its possible to install yhe window, stick outside tape to the wall and fill the gap with polyurethane foam. After removing ekscess of polyurethane foam, stick inside tape to the wall. In case of easy Access to window its possible to stick tapes after installing window. 4. Installing the window: Window installation should be done according to producent reccomendation. WTO A / WINDOW OUTSIDE TAPES WITH ACRYLIC STRIPE Vapour permeable membrane TOU Outside is dedicated to seal joints between the jamps and the door or window frames from the external side of the partition WTO AB(01) / ONE-SIDED WINDOW OUTSIDE TAPES WITH BUTYL AND ACRYLIC STRIPE Vapour permeable membrane TOU Outside is dedicated to seal joints between the jamps and the door or window frames from the external side of the partition. WTO B / WINDOW OUTSIDE TAPES WITH BUTYL STRIPE Vapour permeable membrane TOU Outside is dedicated to seal joints between the jamps and the door or window frames from the external side of the partition

ADEHSIVE TAPES AND FILMS FOR THE PRINTING AND GRAPHICS INDUSTRY

Flexographic Printing Scapa is a leading supplier of adhesive tapes and films for the printing and graphics industry. Our tapes help to achieve superior printing results - even at higher machine speeds and during longer print runs. Digital plate technologies enable the latest printing machines to achieve superior results at much higher speeds. It’s raised the bar for plate mounting tapes, which must ensure that plates are not lifted at elevated machine speeds. With over 90 years of experience in adhesive tapes production, Scapa offers high technology adhesive solutions for all types of printing needs. Additionally, approaching 20 years of working with flexible packaging leaders in the manufacturing of filmic packaging, labels and corrugated paper, we are experienced in working together to find the best solution for your own specific needs. Corrugated Board The corrugated board market is the world's largest user of flexographic printing products. We can provide print and corrugated cardboard companies with a broad range of flexographic adhesive solutions. Everything from solutions for simple design single-color transport packaging to unusual cartons with elaborate graphics. We can also supply double-sided compressible foam and single and double-sided filmic tapes to make printing on corrugated board faster and easier. Narrow Web Printing The Scapa Exafit HP 430µm range features a wide selection of compressible double-sided foam plate mounting tapes for the highest quality narrow web printing process. It features three levels of hardness and two levels of adhesion. Our products cover all label printing processes (solid printing, process and combination) and perform consistently during small print runs and design changes. We also have a complementary range of single and double-sided filmic tapes to make narrow web printing processes faster and easier. Wide Web Printing The Scapa Exafit HP 560µm series offers a wide choice of compressible double-sided foam plate mounting tapes for the highest quality wide web printing. With excellent results for long and quick print runs, the range is available in five levels of hardness and three levels of adhesion. Our tailor-made mounting plate tapes achieve exceptional print quality, coupled with the high level of process efficiency required for flexible packaging. We also have a complementary range of single and double-sided filmic tapes to make wide web printing processes faster and easier. Applications include: Edge Sealing Joining plates to avoid plate lifting during the printing process. Hardmount Range Double-sided films for mounting flexographic photopolymer plates onto cylinders and sleeves. Roll Covering Prevents surface slipping and build up of adhesive and ink on transport rollers. Exafit HP Range Double-sided compressible foam for mounting flexographic photopolymer plates onto cylinders and sleeves. Packaging Bundling and box sealing for packaging applications. Splicing Splicing and joining paper, films and other materials during the printing process.

Description of the Product

PE+Cu Anti bacterial mat is already popular in South Korea. 
We supply as sticky mat , it can be used in clean area

Price of the Product

Price not indicated

Technical Details

Specification
Base Material : LDPE + Cu
Adhesive : Acrylic
Tackiness : 250gf/ 25mm, 400gf/25mm, 600gf/25mm
Thickness : 40um, 50um
Size: 18”*36”, 24”*36”, 600*900(mm), 600*1200(mm)
Layers: 30 layers
Color : Brown(Copper color

Ask for information